Cisco Asa Ssh Crypto Key Generate

Run show crypto key mypubkey rsa to see if you do, in fact, have a key fully generated and registered under a non-default name. If there is, then you can tell the ssh process to use this key with ip ssh rsa keypair-name xxx. If the first command doesn't show anything useful then I'd say you can go ahead and generate a new key. Besides allowing the permitted hosts to SSH to the ASA, you need to define RSA keys for the secure connection. In the CLI: crypto key generate rsa. For these key to work, you should have a hostname/domain-name configured on the ASA as well (unless you configure a dedicated RSA keys).

KB ID 0001322

Problem

I’ve lost count of the number of times this has happened to me! Most of my colleagues prefer to use the ASDM for remote management, but if (like me) you work at command line, then sometimes people <ahem> forget to generate the RSA keypair when deploying a firewall. Then even if SSH access and AAA is setup correctly, you still can’t get in via SSH. Instead you see the following;

RoyalTS and RoyalTSX: ssh_exchange_identification: Connection closed by remote host.

PuTTY: PuTTY Fatal Error: Server unexpectedly closed network connection.

SecureCRT: Connection closed.

OSX/Linux: ssh_exchange_identification: Connection closed by remote host.

Now at command line you can fix this with a ‘Crypto Key Generate RSA Modulus 2048‘ command, but you can’t get to command line only ASDM.

Solution

On older versions of the ASDM you could generate the keypair in the Identification Certificates section (well you still can but only if you are also generating a certificate request file). So, as we are command line warriors, lets use the ASDM’s command line!

Tools > Command Line Interface > Multiple Line

Send > Wait a couple of minutes and try again.

REMEMBER: I’m assuming you have SSH setup correctly if not, see the following article;

Related Articles, References, Credits, or External Links

NA

Cisco Asa Ssh Crypto Key Generate Command

Q: I have a Cisco switch in my network, which I can access by hooking up a console cable directly to the device. I like to access the switch remotely using SSH. How can I enable ssh on my Cisco 3750 Catalyst Switch?
A: By default, when you configure a Cisco device, you have to use the console cable and connect directly to the system to access it. Follow the steps mentioned below, which will enable SSH access to your Cisco devices. Once you enable SSH, you can access it remotely using PuTTY or any other SSH client.

1. Setup Management IP

First, make sure you have performed basic network configurations on your switch. For example, assign default gateway, assign management ip-address, etc. If this is already done, skip to the next step.

In the following example, the management ip address is set as 192.168.101.2 in the 101 VLAN. The default gateway points to the firewall, which is 192.168.101.1

2. Set hostname and domain-name

Next, make sure the switch has a hostname and domain-name set properly.

3. Generate the RSA Keys

The switch or router should have RSA keys that it will use during the SSH process. So, generate these using crypto command as shown below.

Also, if you are running on an older Cisco IOS image, it is highly recommended that you upgrade to latest Cisco IOS.

Product key generator for games. Last addedDate2020-04-13SerialsdateratingToday100%56%44%71%59%57%39%32%33%24%14%0%33%41%38%38%35%30%30%30%33%25%20%50%50%50%50%94%56%57%52%52%45%38%36%35%35%26%50%45%97%94%91%90%89%89%90%100%88%88%87%Try search as.

4. Setup the Line VTY configurations

Setup the following line vty configuration parameters, where input transport is set to SSH. Set the login to local, and password to 7.

Asa

If you have not set the console line yet, set it to the following values.

5. Create the username password

If you don’t have an username created already, do it as shown below.

Note: If you don’t have the enable password setup properly, do it now.

Make sure the password-encryption service is turned-on, which will encrypt the password, and when you do “sh run”, you’ll seee only the encrypted password and not clear-text password.

5. Verify SSH access

From the switch, if you do ‘sh ip ssh’, it will confirm that the SSH is enabled on this cisco device.

After the above configurations, login from a remote machine to verify that you can ssh to this cisco switch.

Cisco Asa Ssh Crypto Key Generate Rsa Modulus 1024 Not Working In Packet Tracer

In this example, 192.168.101.2 is the management ip-address of the switch.

> Add your comment

If you enjoyed this article, you might also like.


Crypto Key Generate Rsa Command


Next post: How to Backup Oracle Database using RMAN (with Examples)

Ssh From Cisco Asa

Previous post: How to Use C++ Single and Multiple Inheritance with an Example